CURRENT INVENTORY

If you are looking for a specific piece of equipment, please call us. We have an extensive inventory of quality equipment available. Call Peter or Basil Yioulos @ 480-483-8361.

TAKE ME TO:

*  HOME PAGE  *  QUOTE REQUEST PAGE  *

ACCUMULATION TABLES

  • Accumulation Tables, rotary and belt type. (photo)

Back to Table of Contents

 

AIR CLEANERS

Back to Table of Contents

 

BAG DUMPERS

  • Semco Systems Bag Dump System, model TBS, w/dust collector, all s/s, size 14A blower with 2HP 3450 rpm 230/460 volt motor. (2 available). (photo)

Back to Table of Contents

 

BAG SEALERS

  • CVP Bag Sealer, model A-300, on stand with casters.

Back to Table of Contents

 

BATTER & BREADING

  • Heat & Control Breader, Batter, & Duster System, model BA-3-36, BD-3-6.

Back to Table of Contents

 

BEAN EQUIPMENT
Back to Table of Contents

 

BLANCHERS

  • Hughes Hot Water Rotary Blancher, 4' wide x 24' long, all s/s construction, hydraulic lift cover, 1/16" perforated reel, clean-out doors. (photo)

Back to Table of Contents

 

BLENDERS & MIXERS

  • Aaron Stainless Steel Double Ribbon Blender, 72 cu. ft., 40” wide x 8’ long, 8” diameter center bottom discharge, 20 HP (2 units).

  • Breddo Likwifier, model LDT 600, s/n D188494-03114, 600 gallon capacity, dual 40 HP motors, 230/460 volt, 3 phase, 2 1/2" outlets with Tri-clamp fittings. Tank is 8' long x 4' wide x 34" deep.  (photo)

  • CE Howard Paddle Blenders (2), style #14969, 42" wide X 7' long X 51" deep, 700 gallon capacity, U trough bottom w/3" bottom ball valve, all s/s construction, single shaft with 3 sets of paddles, on load cells with Weigh-tronics model WI-125 digital scale head.

  • Paddle Blender, 15 cubic foot capacity, all s/s. (photo)

    • Back to Table of Contents

     

    CARTONERS & WRAPPERS
    Back to Table of Contents

     

    CASE FORMERS, SEALERS, & TAPERS
    Back to Table of Contents

     

    CENTRIFUGES / DRYERS

  • Brothers Spin Dryer, all s/s, 2' diameter x 2' deep s/s removable perforated basket, 3/16" perforations, rated at 60 lb. capacity, 5HP 230/460 volt motor, safety switch, timer and controls (2 available).

Back to Table of Contents

 

CHILLERS

  • Carrier Chiller, model 30 GT-040-501, s/n S3592F16966, compressor A1 30GT508092C, compressor B1 30GT508087C, heat exchanger model 10HB 402-011-01. Comes with 20HP 4" Deming Centrifugal Pump.

  • Chester Jensen Plate Chiller, model XB-3-OT-3-32, 3 plate (2 available).

  • Chester Jensen Plate Chiller, model XB-2-OT-2-32, 2 plate (2 available).

Back to Table of Contents

 

COATING PAN

  • Coating Pan, s/s, 36" diameter x 17" deep drum with 18" wide hole, variable speed drive.

Back to Table of Contents

 

COLLOID MILL

  • Charlotte Colloid Mill, model SD 20, s/s product contact, 20HP 3460rpm 230/460 volt 3 phase motor.

Back to Table of Contents

 

CONVEYORS

  • Allen Kenasco Bin Dump Hopper / Conveyor, 24" wide flighted belt elevator, 2" high flights on 8" centers, 12' long elevator, hydraulic drive.

Back to Table of Contents

 

DEAERATORS

  • Cornell Versator, model D-16, s/s contacts, 10 HP Reeves vari-speed drive, 230/460 volt.

Back to Table of Contents

 

DUMPERS (Bin / Tote)

  • FPEC Dumper, model HLD 725, 44" wide, s/s with m/s legs, 2HP hydraulic pump.

Back to Table of Contents

 

EXTRUCTORS
Back to Table of Contents

 

FEEDERS

  • Grove Dale Trough Belt Feeder, model TB-62, stainless steel frame and legs.

  • Magnuson Shufflo Feeder, model 346001-022, s/n 32811, 27" wide. Product from 1/2" up to 5/8", all s/s construction.

  • APC Crepaco Fruit Feeder, model S-420, s/n D-6123, extended hopper. (photo)

Back to Table of Contents

 

FILL/SEAL SYSTEM

  • World Cup Rotary Fill/Seal/Lid System Filler, model 12-32 s/n M1299, 12 station turret, up to 32 oz fill, 4 1/10" diameter cup, pre-cut foil "Tamper-Evident" heat seal, over cap lid system, agitated hopper.

  • World Cup Rotary Fill/Seal/Lid System Filler, model 8-12 s/n 1113, 8 station,  2 1/8" diameter pockets, cup dispenser, pre-cut foil "Tamper-Evident" heat seal, s/s hopper.

Back to Table of Contents

 

FILLERS, SEAMERS, & CAPPERS

  • Canco Seamer, model PUV, rectangular can.

  • Elmar Rotary Piston Filler, model RPE-328C, 28 piston, set 211, 2 3/4" diameter X 8" long pistons, worm to star infeed, counter clockwise rotation.

    • Elmar Rotary Piston Filler, model CCR, 21 piston, 3 3/4" extended pistons, up to 64 oz fill, square s/s clad base, conveyor/worm/star infeed, counter clockwise rotation. Was filling plastic bottles.

  • FMC Granular Filler, model 21-G, s/n HR-813, set 300 diameter cans, brush attachment.

  • FMC Rotary Piston Filler, model C-150, set 300 diameter.

  • FMC Prevacuumizing Syruper, model 125, s/n 4133, set 603 diameter, 12 station, conveyor/worm/star infeed, star discharge.

  • Modern Packaging Inc. Filler, model SL-1x2, s/n MP-254, 3.5 to 5 lb. tub w/tub dispenser, pneumatic, film or foil heat seal, control panel, 240 volt.

  • Pfaudler Rotary Piston Filler w/rising tables, model RP-1421, s/n R575-0297, 21 station, 3 3/4" pistons, s/s product contact, was running 32 oz. plastic containers, worm to star infeed, star discharge, 7/8" diameter discharge ports, 7" long filling spouts, electro pneumatic no can no fill, pistons have teflon rings top and bottom, 5HP gear head motor drive 1725 rpm 230/460 volt w/Warner brake, gear box was mfg. by Boston and ratio is 15 to 1. (photo)

  • Pfaudler Rotary Piston Filler, model RP-21, 21 piston, set 401 diameter, square s/s clad base, 3 3/4" diameter X 9 1/2" long pistons, conveyor/worm/star infeed, counter-clockwise rotation.

  • Simplex Single Piston Filler, model AS-1, 2 7/8" diameter X 8 1/2" long filling cylinder, 5/8" O.D. filling spout, 12" X 27" s/s agitated hopper, mounted on s/s table.

    • Zacmi Rotary Piston Filler, s/n 0295-40/3, 40 valve, set 300 diameter cans, 2 1/4" diameter x 11" long pistons, conveyor/worm/star infeed, counter clockwise rotation, all s/s construction, with seamer motor drive, on s/s base.
Back to Table of Contents

 

FORM, FILL, & SEAL / SCALES

  • Ishida Scale, model CCW-RZ-214 W-S/60-WP, s/s washdown unit, 14 buckets, dimple buckets/hoppers/and vibratory pans. Scale is complete with control system. Electrical is 460 volt, 60hz, 3 phase. Very good condition.

  • Ishida Scale, model CCW-S-212 ST, 14 head, smooth buckets, s/n 12958, remote operation, 1191-2380 grams, Heat & Control s/n P-287-860, 8" x 5" x 8" deep buckets, control panel.

  • Ishida Scale, model CCW-S-212 ST, 14 head, smooth buckets, s/n 12959, remote operation, 1191-2380 grams, Heat & Control s/n P-287-860, 8" x 5" x 8" deep buckets, control panel.

  • Hayssen Bagger, model 15-22-HR, s/n U85849, touch pad control panel, s/s washdown unit.

  • Hayssen Bagger, model 15-22-HR, s/n U85811, touch pad control panel, s/s washdown unit.

  • Triangle Bagger, model SB95C, s/n 118263, s/s washdown unit.

Back to Table of Contents

 

FREEZERS

  • Frigoscandia "FLoFREEZE" Freezer, s/n 00312059, vibratory shaker bed.

Back to Table of Contents

 

GRINDERS

  • Weiler Grinder, model 868, s/n 85-288, s/s with s/s frame, 178D-6H gearbox, 50 HP undermount motor, 1775 rpm 440 volt motor. #1094 barrel, hopper is #112-2093S, auger is 868SS, GW-6-4-75B, 102479. Unit has 5 - 3 blade s/s cut off knives with removable blades, 4 packs of new blades, 1" diameter plate, .130 diameter plate and .500 diameter plate. (photo)

  • Weiler Gearbox, model 1992-5HA, s/n 594B. (photo)

  • Weiler Gearbox, model 1992-5HB, s/n 718M. (photo)

Back to Table of Contents 

 

INJECTORS
Back to Table of Contents

 

JUICE EXTRACTORS
Back to Table of Contents

 

KETTLES & TANKS

  • Groen Kettles, 150 gallon, dual motion scrape agitation, 125 psi, 2" center bottom outlet.

  • Groen Steam Jacketed Kettle, model N-20, 20 gallon, 80 psi, s/n & National Board #129116, 1 5/8" center bottom outlet, s/s legs, 1986, very good condition. 

  • Groen Steam Jacketed Kettle, model D-80, 80 gallon, tilting kettle, 40 psi, National Board #78411, s/s frame and legs, 1976, very good condition.

  • Groen Steam Jacketed Kettle, model DN-100, 100 gallon, tilting type, 75 psi, all s/s, National Board #139762.

  • Groen Steam Jacketed Kettle, model INA 150, 150 gallon, single motion slant scrape agitation, 100 psi.

  • Groen Steam Jacketed Kettle, model N-150, 150 gallon, 2" center bottom bevel seat outlet, 100 psi.

  • Hamilton Steam Jacketed Kettle, model SA, s/n 4930, 150 gallon, double motion scrape agitation, tilt out agitator, 100 psi, 3" center bottom outlet with pneumatic gate discharge, National Board #186.

  • Lee Vacuum Pan, model 150 D7S, s/n B799OD1, 150 gallon, 90 psi, scrape agitation, National Board #5561.

Back to Table of Contents

 

LABELERS

  • Quadrel Labeler, model Q-60, on s/s stand w/casters, new in 2005.

Back to Table of Contents

 

METAL DETECTORS

  • Fortress Metal Detector, model Phantom, 4" high X 20" wide aperture (3" above belt clearance), 18" wide X 52" long plastic intralox belt, all s/s washdown unit, slider bed reject system with alarm, 1/2 HP 208/230/460 volt gear motor, on casters, excellent condition.

  • Goring Kerr Drop Thru Metal Detector, last used in pasta plant.

    • Safeline "Pipeline" Metal Detector, 2" diameter, s/s washdown unit, completely rebuilt, (2) available. (photo)

  • Safeline "Pipeline" Metal Detector, 3" diameter, s/s washdown unit, completely rebuilt. (photo)

Back to Table of Contents

 

FITZMILLS

  • Fitzpatrick Fitzmill, model DASO-6, s/n 7246, 7 1/2 HP 208/230/460 volt motor, fair to good condition.

Back to Table of Contents

 

OVENS

Back to Table of Contents

 

PACK OFF TABLES

Back to Table of Contents

 

PALLETIZER / DEPALLETIZER 

  • Whallen Palletizer/Depalletizer, with control panel.

Back to Table of Contents

PARTS

  • Bettcher Slice-N-Tact Harp Set, 3.0mm for model BH-15.

  • Bettcher Slice-N-Tact Harp Set, 5.0mm for model BH-15.

Back to Table of Contents

 

PASTURIZER / COOLER

Back to Table of Contents

 

PEELERS

  • Gering Onion Peeler.

  • Hobart Batch Peeler, model 6430-T, all s/s construction, 200/230 volt.

  • Lyco Peeler, model 7000, 7 roll (5 abrasive, 2 brush), hydraulic drive, no power pack, center retarding auger.

Back to Table of Contents

 

PULPERS / FINISHERS

Back to Table of Contents

 

PUMPS

  • APV Centrifugal Pump, model 8VS2, 3" in/2" out Tri-clamp, 5HP 1745 rpm motor, 230/460 volt.

  • Busch Vacuum Pump, model RA-0250, 10HP motor.

    • (photo)

  • Cornell Hydro Food Pump,model 4NMT-2R, 4" dia., single port, stainless steel casting, 3 HP motor drive. (photo)

  • Cornell Hydro Food Pump, 6", model #6NHPP-F16K, s/n 2265 13.5, s/s casting, 5HP 208/230/460 volt motor 1700 rpm, mounted on s/s frame. Very good condition.

  • Cornell Hydro Food Pump, 6", w/stainless steel vortex hopper, 10 HP motor drive.

  • Cornell Hydro Food Pump, 8", stainless steel w/vortex hoppers. (photo)

  • Graco Tote Pump System, serial number BA 103, 43 1/2” x 40 1/4” platen, model 625-794 series J99A, Bulldog pneutatic pumps with controls, all stainless steel construction.

    • (photo)

  • Sandpiper Diaphram Pump, model SB2-A, type TGN-2-SS, s/n 369701, 3" tri-clamp in/2 1/2" tri-clamp out, all s/s.

  • Waukesha Positive Displacement Pump, model 060, s/n 142868, s/s base, 5HP gear motor.

  • Waukesha Positive Displacement Pump, model 130, 3" in/out, s/s base w/casters, 5HP 230/460 volt motor w/gear box.

  • Waukesha Positive Displacement Pump, model 130, s/n 269620-00, 3" in/out, vented cover, 7.5HP 230/460 volt motor, 1745 rpm, s/s base.

  • Waukesha Positive Displacement Pump, model 220, s/n 214920-98, s/s base, 20HP gear motor. (photo)

  • Waukesha Positive Displacement Pump, model 220, s/n 214920-98, s/s base. (photo)

  • Wilden Diaphram Pump, model T8/SAPB/TF/TF/STF, s/n 0020284507, 2" in/out, 316 s/s, Item #08-11234, m/o #422040.

Back to Table of Contents

 

SCREW CONVEYORS 

  • Screw Conveyor, 9" x 16' long, all s/s construction, shaft mounted gear reducer

  • Screw Conveyor, 9" x 10' long, all s/s construction, 2HP gear head motor drive.

  • Screw Conveyor, 9" x 5' long, all s/s construction, shaft mounted gear reducer.

Back to Table of Contents

 

SEPARATORS

  • Sweco Separator, 48" diameter, single deck, 1 HP 230/460 volt motor, painted steel base.

Back to Table of Contents

 

SHAKERS - VIBRATORY

  • Allen Vibratory Conveyor, 30" wide x 5'6" long, solid pan, s/s construction.

  • Hughes Vibratory Dewatering Shaker, model 22-0323-51, s/n 94-16172, 18" wide X 5' long, removable 1/16" spacing between rods, drain pan discharge, all s/s construction, Ajax shaker, good condition.

  • Key Technology "Iso-Flo" Vibratory Dewatering Shaker, model 421788-1APFF, s/n 97-24036, 24" wide X 6' long, (2) 24" wide X 31" long removable screen sections, drain discharge pan, all s/s construction, below bed frame, pedestal legs, Key "Iso Drive" with 1HP drive motor, very good condition.

  • Key Technology Vibratory Dewatering Shaker, model 405075-10, 30" wide X 6 1/2' long nylon mesh screen, s/s water/product spreader, 1HP 208/230/460 volt motor with Key "Iso Drive", mounted on 3' wide X 5 1/2' long s/s rectangular reclaim tank, with 4" Cornell Hydro Food Pump, model 4NMTR, and Rosedale Products s/s water filtration system.

  • Key Technology "Iso-Flo" Vibratory Grader, model 426158-1, s/n 98-37365, 30" wide X 6' long, (2) 30" wide X 24" long removable slotted screen sections (slots 3/8" wide X 1 1/4" long), all s/s construction, below bed frame, pedestal legs, Key "Iso Drive" with 1HP drive motor, very good condition.

  • Key Technology "Iso-Flo" Vibratory Grader, model 425252-1, s/n 97-29070, 30" wide X 8' long, (1) removable slotted screen (slots 3/8" wide X 1 1/4" long), all s/s construction, below bed frame, pedestal legs, Key "Iso Drive" with 1HP drive motor, very good condition.

  • Key Technology "Iso-Flo" Dewatering Shaker / Grader, single deck, 24" wide X 8' long, above bed frame, all s/s construction, Key "Iso Drive" with 1HP drive motor, 1/4" wide rods on screen, (2) 24" X 24" screen sections.

    • (photo)

  • Key Technology "Iso-Flo" Vibratory Conveyor, model number 421585-1, s/n 95-14479, 24" wide X 6 1/2' long bed with bias/spreader discharge, partial cantilever frame style, all s/s construction (613 finish), Key "Iso Drive" with 1HP drive motor.

    • Key Technology "Iso-Flo" Vibratory Conveyor, 24" wide X 6' long, has 4' long solid pan, s/s construction.  

  • VAV Scan-Vibro Vibratory Feed Shaker, type FR, 45" wide X 66", 2 shaker motors. (photo)

Back to Table of Contents

 

SIFTERS
Back to Table of Contents

 

SIZE REDUCTION

  • Bettcher Slice-n-Tact Slicer, model BH-15, all s/s construction, includes harp set (3 mm or 5 mm), 230/460 volt.

  • Sprout Waldron Disc Mill, 24", 25HP.

  • Urschel Comitrol Processor, model 1700, s/n 2544, 3" cutting head, 30HP brake motor, no oil mist lube system, 6" pulley on motor and 4" pulley on spindle.

  • Urschel Comitrol Processor, model 3600, s/n 625, cutting head, auger feed, 10HP 230/460 volt motor, factory control panel with safety interlocks, s/s base with casters. (photo)

  • Urschel Dicer, model GA, set 3/8" dice, factory control panel, safety disconnects, 2HP 230/460 volt motor. (photo)

  • Urschel Dicer, model H, 1 1/8" crosscut spindle, s/s frame.

  • Urschel Dicer, model L-A, s/n 557, factory control panel, set for 1/2" dice, 2 HP vari-speed 230/460 motor.

  • Urschel Slicer / Shredders (2), model CC.

  • Urschel Slicer, model OV, 16 blade slicing head, factory control panel, safety disconnects, 2HP motor.

  • Urschel Strip Cutter, model GRL, factory control panel, 2HP motor. (photo)

  • Urschel Translicer, model TRS 2500, factory control panel, safety disconnects, cutting wheel assembly, all s/s construction, very good condition. (photo)

  • Urschel Translicer, model TRS 2500, factory control panel, cutting wheel assembly, all s/s construction, very good condition.

Back to Table of Contents

 

SIZERS / GRADERS
Back to Table of Contents

 

SKINNERS
Back to Table of Contents

 

UNLOADING SYSTEMS (Bin / Tote)

  • Graco Tote Pump System, s/n BA 103 and BA 104, 43 1/2" X 40 1/4" platen, model 625-794 series J99A Bulldog pneumatic pumps with controls, all stainless steel construction, excellent condition.  (photo)

Back to Table of Contents

 

URSCHEL

  • Urschel Comitrol Processor, model 1700, s/n 2544, 3" cutting head, 30HP brake motor, no oil mist lube system, 6" pulley on motor and 4" pulley on spindle.

  • Urschel Comitrol Processor, model 3600, s/n 625, cutting head, auger feed, 10HP 230/460 volt motor, factory control panel with safety interlocks, s/s base with casters.  (photo)

  • Urschel Dicer, model GA, set 3/8" dice, factory control panel, safety disconnects, 2HP 230/460 volt motor.  (photo)

  • Urschel Dicer, model H, 1 1/8" crosscut spindle, s/s frame.

  • Urschel Dicer, model L-A, s/n 557, factory control panel, set for 1/2" dice, 2 HP vari-speed 230/460 motor.

  • Urschel Slicer / Shredders (2), model CC.

  • Urschel Slicer, model OV, 16 blade slicing head, factory control panel, safety disconnects, 2HP motor.

  • Urschel Strip Cutter, model GRL, factory control panel, 2HP motor.  (photo)

  • Urschel Translicer, model TRS 2500, factory control panel, safety disconnects, cutting wheel assembly, all s/s construction, very good condition. (photo)

  • Urschel Translicer, model TRS 2500, factory control panel, cutting wheel assembly, all s/s construction, very good condition.

Back to Table of Contents

 

URSCHEL PARTS

If you are in need of an Urschel part that is not listed here, please call us at 480-483-8361 as we have an extensive inventory of parts that are not listed.

Urschel Model CC Parts

(MOST ITEM DESCRIPTIONS ARE FOLLOWED BY URSCHEL PART NUMBER IN BOLD NUMBERS)

  • Cutting Head Assembly, flat slice, bronze.  (part #22140)

  • Cutting Head Assembly, crinkle slice, bronze.  (part #22166)

  • Cutting Head Assembly, V slice, .125 V, bronze.  (part #22170)

  • Impeller Drive Assembly, bronze, rebuilt.  (part #22172)

Urschel Model Comitrol 1700 Parts

(MOST ITEM DESCRIPTIONS ARE FOLLOWED BY URSCHEL PART NUMBER IN BOLD NUMBERS)

  • Cutting Head, 3B-010030.  (part #66197)

  • Cutting Head, 3B-010040.  (part #66198)

  • Cutting Head, 3B-015015.  (part #66787)

  • Cutting Head, 3B-020020.  (part #66786)

  • Cutting Head, 3J-030300.  (part #66569)

  • Cutting Head, 3K-010020.  (part #66752)

  • Cutting Head, 3K-015025.  (part #66413)

  • Cutting Head, 3K-030090U.  (part #66770)

  • Impeller, 3 paddle, straight, 3".  (part #66214)

  • Impeller, 3 paddle, forward slant, 3".  (part #66590)

  • Impeller, 9 paddle, .650 Uni-Cut, Seal.  (part #66806)

  • Impeller, 9 paddle, .650 Veri-Cut.  (part #67004)

  • Lower Retaining Ring.  (part #62873)

Urschel Model DiversaCut 2110 Dicer Parts

(MOST ITEM DESCRIPTIONS ARE FOLLOWED BY URSCHEL PART NUMBER IN BOLD NUMBERS)

  • Stripper Plate, 1/4", s/s.  (part #42398)

Urschel Model G-A Parts

(MOST ITEM DESCRIPTIONS ARE FOLLOWED BY URSCHEL PART NUMBER IN BOLD NUMBERS)

  • Bearing Block, 1/2".  (part #13054)

  • Bearing Housing.  (part #12009)

  • Crank Bearing Block, 3/8" 16 knives.  (part #13152)

  • Crank Bearing Block, 1/2" 12 knives.  (part #13048)

  • Crank Bearing Block, 5/8" 10 knives.  (part #13154)

  • Crank Bearing Block, 3/4" 8 knives.  (part #13616)

  • Gate Extension Strip, 1/8" - 11/32".  (part #12187)

  • Gate Extension Strip, 3/8" - 15/32".  (part #12190)

  • Gate Extension Strip, 1/2" - 3/4".  (part #12192)

  • Hinge Tube, w/bearings.  (part 12201)

  • Motor, with brake, 2HP, 184 frame.  (part #13754)

  • Shaft, main drive. (part #12199)

  • Shaft, jack. (part #12200)

  • Shaft, impeller. (part #12436)

  • Slicing Knife, straight cut.  (part #13104)

  • Slicing Knife, crinkle cut. (part #14023)

  • Slicing Knife, for peaches. (part #13245)

  • Slicing Knife Holder, 1/8", s/s. (part #13016)

  • Slicing Knife Holder, for peaches. (part #13071)

  • Spindle Assembly, circular, 3/4", s/s. (part #13417)

  • Spindle Assembly, crosscut, 9/32" (22 knife), s/s. (part #13344)

  • Spindle Assembly, crosscut, 3/8" (16 knife), s/s. (part #13322)

  • Spindle Assembly, crosscut, 1/2" (12 knife), s/s. (part #13299)

  • Spindle Assembly, crosscut, 3/4" (8 knife), s/s. (part #13612)

  • Stripper Plate, 5/8". (part #13030)

  • Stripper Plate, 5/32", julienne cut. (part #13113)

  • Support Bar, clamp end. (part #12208)

Urschel Model M Parts

(MOST ITEM DESCRIPTIONS ARE FOLLOWED BY URSCHEL PART NUMBER IN BOLD NUMBERS)

  • Circular and Crosscut Blades.

  • Crosscut Spindles, 3/16", 3/8", 1/2", 3/4".

    •   (part #45202, 45227, 45266, 45366)

  • Crosscut Lift.

    • (part #45501)

  • Feed Belts.

    • (part #16918)

  • Feed Drums, 3/8", 1/2", 1".

    • (part #45299, 45300, 45302)

  • Feed Rolls, 1/4", 3/8".

    • (part #45212, 45283)

  • Gears.

  • Spacers, 5/8", 3/4", 1".

    • (part #16109, 16110, 16121)

  • Stripper Plates. (part #45075, 45240, 45285, 45296, 45312)

 Urschel Model OV Parts

(MOST ITEM DESCRIPTIONS ARE FOLLOWED BY URSCHEL PART NUMBER IN BOLD NUMBERS)

  • Motor Pulley Assembly, 38 and 16 teeth. (part #29019)

  • Slicing Wheel Assembly, 3/16", 22 knife. (part #27152)

  • Slicing Wheel Assembly, 1/4", 16 knife. (part #27150)

  • Slicing Wheel Assembly, 17/64", 15 knife. (part #27148)

  • Slicing Wheel Assembly, 9/32", 14 knife. (part #27146)

  • Slicing Wheel Assembly, 5/16", 13 knife. (part #27144)

Urschel Model Q Parts

(MOST ITEM DESCRIPTIONS ARE FOLLOWED BY URSCHEL PART NUMBER IN BOLD NUMBERS)

  • Ball Bearing, 35 mm ID, 62 mm OD.

    • (part #53192)

  • Bearing Assembly.

    • (part #53199)

  • Bearing Cartridge, single bearing.

    • (part #53200)

  • Bearing Holder.

    • (part #53191)

  • Bearing Holder Clamp, crosscut.

    • (part #53113)

  • Bearing Housing, jack shaft.

    • (part #53034)

  • Bearing Sleeve, replacement. (part #53198)

  • End Cap. (part #53036)

  • Gear, 10P, 27T, 1.125" ID, ss. (part #53050)

  • Handle Assembly, feed hopper door. (part #53451)

  • Impeller Shaft. (part #53023)

  • Knife, slicing, str, replacement insert. (part #52178)

  • Pulley, timing, 22 teeth, DAYCO. (part #53149)

  • Pulley, timing, 29 teeth, DAYCO. (part #53150)

  • Pulley, timing, 38 teeth, RPP 8 mm. (part #53151)

  • Pulley, timing, 83 teeth, RPP 8 mm. (part #53154)

  • Pulley Hub (used). (part #53035)

  • Retaining Rings, w/screws. (part #53061)

  • Spacer, 3/16", 2.5" OD, .058 th knife. (part #16182)

  • Slicing Knife Holder, 3/16", 1/2". (part #53366, 53173)

  • Spindle Assembly, circular, 3/16". (part #53364)

  • Spindle Assembly, crosscut, 5/8", str, thin. (part #53377)  

  • Spindle Assembly, crosscut, 1", str, thin. (part #53380)

  • Spindle, circular knife, w/nut. (used) (part #53109)

  • Spindle, circular knife, w/(42) 1/4" spacers and nut. (used) (part #53109)

  • Spindle, crosscut, 1/4", w/retaining rings. (part #53090)

  • Spindle, crosscut, 1/2", w/retaining rings. (part #53094)

  • Spindle, crosscut, 1-3/4", w/retaining rings. (part #53381)

  • Stripper Plate Adjustment Bar. (part #53215)

  • Stripper Plate Adjustment Support. (part #53212)

  • Stripper Plate, 3/32", long. (part #53441)

  • Stripper Plate, 1/2", long. (part #53186)

  • Stud, 3/8-16 x 1.938" long, 17-4 PH, ss. (part #53491)

  • Timken Bearing Cone, modified bore. (part #53432)

Urschel Model RA-A Parts

(MOST ITEM DESCRIPTIONS ARE FOLLOWED BY URSCHEL PART NUMBER IN BOLD NUMBERS)

  • Feed Drum, 3/16", wide slot. (part #18589)

  • Feed Drum, 1/4", wide slot. (part #18582)

  • Gear, 8P, 49T, 1.5" ID, nylon. (part #18023)

  • Gear, 10P, 19T, .75" ID, s/s. (part #48040)

  • Gear, 10P, 52T, .875" ID, MAB. (part #48039)

  • Gear, 10P, 68T, 2" ID, nylon. (part #19016)

  • Gear Hub, shear pin. (part #19019)

  • Hub, shear pin. (part #19017)

  • Hub. (part #48098)

  • Impeller Shaft Assembly.  (part #19272)

  • Spindle Assembly, circular, 9/16", s/s, HD. (part #18599)

  • Spindle Assembly, crosscut, 1/8", 24 knife, plated bronze. (part #18122)

  • Spindle Assembly, crosscut, 3/16", 16 knife, plated bronze. (part #18123)

  • Spindle Assembly, crosscut, 1/4", 12 knife, plated bronze. (part #18139)

  • Spindle Assembly, crosscut, 3/8", 7 knife, s/s. (part #19268)

  • Spindle Assembly, crosscut, 3/4", 4 knife, s/s. (part #19283)

Urschel Translicer 2500 Parts

(MOST ITEM DESCRIPTIONS ARE FOLLOWED BY URSCHEL PART NUMBER IN BOLD NUMBERS)

  • Cutting Wheel Assembly, julienne, 24 blade wheel w/4 julienne knives, 1 3/8" x 1 1/2" cut. (part #51052)  (hub #51044)

  • Cutting Wheel Assembly, julienne, 24 blade wheel w/4 julienne knives, 1 3/8" x 2" cut. (part #51314-HD)  (hub #51044)

  • Cutting Wheel Assembly, shredding, 22 blade wheel w/11 slicing knives and 11 julienne knives, 1/8" x 2" shred. (part #51504)

  • Cutting Wheel Assembly, slicing, 24 blade wheel w/24 straight knives, 1/16" slice. (part #51046)  (hub #51041)

  • Cutting Wheel Assembly, slicing, 24 blade wheel w/4 straight knives, 1 1/2" slice. (part #51046)  (hub #51041)

  • Cutting Wheel Assembly, slicing, 22 blade wheel w/22 straight knives, 3/16" slice. (part #51047)  (hub #51042)

  • Cutting Wheel Assembly, slicing, 16 blade wheel w/16 straight knives, 1/4" slice. (part #51048)  (hub #51043)

  • Cutting Wheel Assembly, slicing, 24 blade wheel w/6 straight knives, 1" slice. (part #51049)  (hub #51044)

  • Cutting Wheel Assembly, slicing, 24 blade wheel w/12 straight knives, 1/2" slice. (part #51049)  (hub #51044)

  • Feed Belts, primary, smooth, blue.  (part #51104)

  • Translicer displayed w/variety of cutting wheels (over 20 cutting wheels in stock).  (photo)

Urschel Model W Parts

(MOST ITEM DESCRIPTIONS ARE FOLLOWED BY URSCHEL PART NUMBER IN BOLD NUMBERS)

  • Cutting Roll, 5/32", bronze.  (part #38008)

  • Spindle Assembly, circular, 5/32", 72 knives.  (part #38017)
Back to Table of Contents

 

    WAREHOUSE

  • Busse Unloaders (2), model BSC.

Back to Table of Contents

 

WATER TREATMENT

  • Sweco Hydrasieve, 72" wide, all s/s construction.

Back to Table of Contents
Go to Quote Request Page
Back to Home Page

Delphi International buys and sells used food processing and packaging equipment including Urschel, Urschel slicers, Urschel dicers, Urschel Parts, Groen kettles and tanks, Vanmark peelers, Magnuson, Ishida scales, Fortress, Cintex, Goring Kerr, and Safeline metal detectors, Key vibratory and dewatering shakers, Angelus seamers, Key shakers and graders, Hughes blanchers, Breddo likwifiers, Zacmi fillers, Elmar, Rietz extructors, Waukesha pumps, Canco seamers and cappers, Krones labelers, Bock centrifuges, Graco, CVP bagger sealers, M-Tek, Shufflo feeders, Langsenkamp pulpers and finishers, Marlen pumps, Hobart mixers, Bauer hydrasieves, Sweco separators, as well as casers,  bean snippers, tote dumpers, barrel dumpers, ribbon blenders, fitzmills, etc.